Reamers blogMachine Reamers MT1 / .3674 Small End Dia. / .5170 Large End Dia. / 3″ LOC / 6-5/16″ OAL / Finishing
Machine Reamers MT1 / .3674 Small End Dia. / .5170 Large End Dia. / 3″ LOC / 6-5/16″ OAL / Finishing High Speed Steel Taper Shank Price: $ 60.38
Hand Expansion Reamers Spiral and Straight Flute 3/4″ / 2-11/16″ LOC / 7-1/16″ OAL / Straight Flute
Hand Expansion Reamers Spiral and Straight Flute 3/4″ / 2-11/16″ LOC / 7-1/16″ OAL / Straight Flute High Speed Steel NOTE: Expansion hand reamers are primarily designed for work where it is necessary to enlarge reamed holes by a few thousandths. Maximum Expansion Limit: 1-4″ – 7-16″ .006″ 1/2″ – 7/8″ .010″ 1″ – 1-1/4″ [...]
Alvord Polk 131-0 High-Speed Steel Chucking Reamer, Straight Flute, Taper Shank, Uncoated Finish, Size: 1/4 Inch
Alvord Polk 131-0 High-Speed Steel Chucking Reamer, Straight Flute, Taper Shank, Uncoated Finish, Size: 1/4 Inch Straight flute reamers are recommended for general purpose reaming to make minor enlargements to preformed holes with a very precise size and roundness Straight flute reamers are good for use in through or blind holes without interruptions such as [...]
Beadalon Pearl Reamer, Fine
Beadalon Pearl Reamer, Fine Designed to enlarge and smooth out drill holes in pearls Made in USA Sharp, corkscrew-like file fits easily into the hole of any small pearl Simply slide a pearl onto the file, and slide the pearl back and forth until desired interior diameter is reached Also a great tool for removing [...]
ISO 2238:1972, Machine bridge reamers
ISO 2238:1972, Machine bridge reamers This International Standard specifies the characteristics of machine bridge reamers. It gives, for a series of diameter ranges d from 6 to 50.8 mm (0.236 2 to 2.000 0 in),the values in millimetres and inches for the following dimensions of these tools verall length L; total cutting edge length l; [...]
Alvord Polk 155-2 High-Speed Steel Taper Pin Reamer, Left Hand Spiral Flute, Round Shank, Uncoated Finish, Size Number: 0
Alvord Polk 155-2 High-Speed Steel Taper Pin Reamer, Left Hand Spiral Flute, Round Shank, Uncoated Finish, Size Number: 0 Left-hand spiral reamers are recommended for reaming holes with interruptions, as they prevent damage to the workpiece edge and tool Left-hand spiral reamers are good for use in through holes (holes that extend all the way [...]
H.D. Cylinder Ridge Reamer (3″ – 5″ Range)
H.D. Cylinder Ridge Reamer (3″ – 5″ Range) Tungsten carbide cutters remove ridges from top of cylinders. A must before replacing piston rings. For use on 3″ – 5″ (77mm – 127mm) cylinder diameters. Smooth cutting is assured by fine thread feeding. Changing from one cylinder to another without readjusting is easy with the three [...]
Repl. Cutter Blades for H.D. Cylinder Ridge Reamer
Repl. Cutter Blades for H.D. Cylinder Ridge Reamer Set of replacement cutter blades for the H.D. Cylinder Ridge Reamer. Price: $ 11.50